Collection

Depending on its parameterization the MDT Glass Push Button II Lite releases KNX telegrams. The sensor areas can be programmed for 1 or 2 button operation (BE-GTL4xx.01: 4 single sensor buttons). The RGBW status LEDs can be controlled with internal or ext

The MDT KNX Power Supply with integrated choke supplies the KNX Bus with a constant, stabilized 30VDC voltage. The integrated bus coupling unit with diagnostic function monitors the bus voltage, bus current, bus overload and bus voltafe failure/return. Al

The MDT KNX/EIB Power Supply with integrated choke produces the stabilized KNX system voltage (30VDC) to supply the connected KNX/EIB components. The operating status is indicated via 3 LED.

The inputs of the MDT Universal Interface react depending on their programmed parameters and send a telegram on the KNX bus.
You can connect conventional push-buttons or auxiliary contacts (eg door and window contacts) to the device

KNX IP Router: This Interface offers the same functions as the IP interface, but the device routes telegrams as a line coupler using the the LAN.

Wireless KNX RF S-Mode Temperature and Relative Humidity Sensor.
The communication with the bus must be done by using a KNX/KNX RF S-Mode media coupler.

Passive infrared detector for ceiling installation
Horizontal 360° motion detection area
Presence/motion detection up to 64 m² / 400 m² (depending on mounting or room height)

Enhance your home automation with xxter iBeacons: location-based scenes, access, and presence detection without GPS.

2 channels
Electrically interlocked relays to reverse the direction of rotation
Integrated electronics for detection of the actuation of an electromechanical limit switch and with auto-calibration of the travel time from one limit switch to the other

The KNX RF / ENO Push Button 440 secure unites two wireless protocols in one device: EnOcean and KNX RF. Out of the box the push button operates in EnOcean mode.

OFFERS SPECIAL PRODUCT FEATURES SUCH AS
Presence and daylight-dependent constant light control
KNX functions: alarm, twilight switch, brightness detection, light-dependent motion detection, snooze function, scene telegram via object

The measuring system SK08-BFT-WMT records the soil moisture and the soil temperature, which is measured with the Watermark® sensor. The measured values can be output and used for control tasks.

Wall box made from galvanised steel. Fits Barchetto 2 and 4 as well as Trico 8RGB. Size ca. 32x112x55

The MDT KNX Push Button releases KNX telegrams after pushing the buttons on top.

The MDT Room Temperature/humidity sensor 55 detects temperature and humidity in indoor rooms, the dew point is calculated automatically. For the sensors the Min./Max values can be set in the paramerization of the device and approbiate actions can be defin

The new AKS series offers more channels at less space, so lower costs per channel.
The MDT Switch Actuator receives KNX/EIB telegrams and switches up to 20 independent electrical loads. Each output uses a bistable relay and can be operated manually via a

Interface with 4 independent channels, which can work as Binary or Analog Input.
The Digital (Binary) inputs which may be conmnected to a conventional push-button, switch or binary sensor with free-voltage contact.

Per input one AC or DC contact in the range of 10...230 V
Per input direct operation function on the device for simulation of input status and indication oft the input status via LED

UP 220/21
Pushbutton interface 2 x potential-free contact, output for LED control
2 inputs / outputs

8 inputs AC/DC 12...230 V
8 relay contact outputs
Rated contact voltage AC 230 V

For data exchange between two KNX bus lines with telegrams of up to 64 byte
For use as line coupler for connecting a line to the main line or as backbone coupler for connecting a main line to the backbone....

The service interface consists of:
OCI702 service interface
USB 2.0 cable (Type A / B)
KNX service cable for Synco™ controllers (RJ45 / RJ45)
KNX service cable for Desigo™ TRA (RJ45 / jack plug 2.5 mm)
KNX service cable (RJ45 / KNX bus terminal)

Compact KNX RF/TP Coupler 673.1 secure for integrating KNX RF devices, supports long frames & KNX Data Security.

Artikel 5238 IP Aktor and Interface
The KNX TP Multi IO 580 (48I/O) is a universal binary interface for building control. It provides 48 I/O lines. Each line can be used as binary input as well as binary output.