Siemens

Touch control TC5 UP 205/22 black or white
Aluminium and glas housing
Capacitive touch colour display 5", 480 x 854 pixels
LED colour light strip as orientation light, respectively to signal alarms
Integrated room temperature sensor

QMX3.P37-1BSC
Room operator unit KNX with temperature sensor, segmented backlit display, configurable touchkeys, LED display, black

Two DALI outputs with DALI-2 certification acc. to IEC 62386-101 and 103, each for communication with up to 64 DALI ballasts

One relay contact per output
Rated contact operating voltage: AC 230 V
Rated contact frequency: 50/60 Hz
Rated contact current: 16 A

For connection of a modular bus device to the bus line
10-pole BTI socket (BTI - Bus Transceiver Interface) for plugging of bus terminal devices with BTI connector

2 channels
Electrically interlocked relays to reverse the direction of rotation
Integrated electronics for detection of the actuation of an electromechanical limit switch and with auto-calibration of the travel time from one limit switch to the other

Passive infrared detector for ceiling mounting indoors
Adjustable sensitivity of detection
Mixed light measurement

KNX Power supply unit DC 29 V, 640 mA with additional unchoked output, N 125/22

Passive infrared detector for ceiling installation
Horizontal 360° motion detection area
Presence/motion detection up to 64 m² / 400 m² (depending on mounting or room height)

Passive infrared detector for ceiling installation
Horizontal 360° motion detection area
Presence/motion detection up to 64 m² / 400 m² (depending on mounting or room height)

UP 220/21
Pushbutton interface 2 x potential-free contact, output for LED control
2 inputs / outputs

For data exchange between two KNX bus lines with telegrams of up to 64 byte
For use as line coupler for connecting a line to the main line or as backbone coupler for connecting a main line to the backbone....

The service interface consists of:
OCI702 service interface
USB 2.0 cable (Type A / B)
KNX service cable for Synco™ controllers (RJ45 / RJ45)
KNX service cable for Desigo™ TRA (RJ45 / jack plug 2.5 mm)
KNX service cable (RJ45 / KNX bus terminal)

Compatible with USB 2.0 and USB 3.0
For isolated access to the bus line over the built-in USB socket (type B)
For connection of a PC for addressing,etc
Support of bus telegrams with up to 64 bytes length

Per input one AC or DC contact in the range of 10...230 V
Per input direct operation function on the device for simulation of input status and indication oft the input status via LED

DIN rail mounted device for mounting on rail TH35 according to DIN EN 60715

8 inputs AC/DC 12...230 V
8 relay contact outputs
Rated contact voltage AC 230 V

8 slots for a sensor/actuator module, type RS or RL
Internal bus cable for connection of the sensor/actuator module to the bus

BACnet Application Specific Controller (B-ASC) as Gateway between KNX TP and BACnet IP
Up to 250 BACnet objects
Up to 455 BACnet COV subscriptions

Four outputs for switching and dimming of resistive, inductive and capacitive loads
Automatic adjustment to leading edge or trailing edge control, depending on the type of load
Rated operational voltage AC 230 V

Rated contact current 10 AX

Passive infrared detector for ceiling installation
Horizontal 360° motion detection area
Presence/motion detection up to 64 m² / 400 m² (depending on mounting or room height)

With 4 inputs / outputs each configurable for potential-free contacts or for control of an LED (max 2 mA)
With integrated bus coupling unit, bus connection via bus terminal
8-wire plug-in cable set, 280 mm long, extendable to a max. of 10 m

For mounting in AP 118 automation module box or AP 641 room control box